# $FreeBSD: head/sys/mips/conf/WZR-HPAG300H.hints 275470 2014-12-03 23:37:23Z sbruno $

# arge0 is connected to the LAN side of the switch PHY.
# arge1 is connected to the single port WAN side of the switch PHY.

hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0

hint.arge.0.phymask=0x0
hint.arge.0.media=1000
hint.arge.0.fduplex=1
hint.arge.0.eeprommac=0x1f05120c
hint.arge.0.mdio=mdioproxy0     # .. off of the switch mdiobus
hint.arge.0.miimode=3 

hint.arge.1.phymask=0x10
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.eeprommac=0x1f05520c
hint.arge.1.mdio=mdioproxy1     # .. off of the switch mdiobus
hint.arge.1.miimode=3 

#
# AR8316 switch config
#
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=0       # We need to be explicitly told this
hint.arswitch.0.numphys=4       # 5 active switch PHYs (PHY 0 -> 4)
hint.arswitch.0.phy4cpu=1       # No, PHY 4 == dedicated PHY
hint.arswitch.0.is_rgmii=1      # Yes, is RGMII
hint.arswitch.0.is_gmii=0       # No, not GMII

# ath0 - slot 17
hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f051000
hint.pcib.0.bus.0.17.0.ath_fixup_size=4096

# ath1 - slot 18
hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f055000
hint.pcib.0.bus.0.18.0.ath_fixup_size=4096
# .. and now, telling each ath(4) NIC where to find the firmware
# image.
hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware"
hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware"

# Inherited from AR71XX_BASE.hints
#hint.mx25l.0.at="spibus0"
#hint.mx25l.0.cs=0
# This board has two 16 MB flash devices on difference Chip Select pins
hint.mx25l.1.at="spibus0"
hint.mx25l.1.cs=1


# Geom MAP

hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00040000
hint.map.0.name="uboot"
hint.map.0.readonly=1

hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end=0x00050000
hint.map.1.name="u-boot-env"
hint.map.1.readonly=1

hint.map.2.at="flash/spi0"
hint.map.2.start=0x00050000
hint.map.2.end=0x00060000
hint.map.2.name="ART"
hint.map.2.readonly=1

# requires a 1M alignment and padding in the image.
# make sure you are using conv=sync and bs=1M in your dd
hint.map.3.at="flash/spi0"
hint.map.3.start=0x00060000
hint.map.3.end="search:0x00160000:0x100000:.!/bin/sh"
hint.map.3.name="kernel"
hint.map.3.readonly=1

hint.map.4.at="flash/spi0"
hint.map.4.start="search:0x00160000:0x100000:.!/bin/sh"
hint.map.4.end=0x01000000
hint.map.4.name="rootfs"
hint.map.4.readonly=1

hint.map.5.at="flash/spi1"
hint.map.5.start=0x00FF0000
hint.map.5.end=0x01000000
hint.map.5.name="cfg"
hint.map.5.readonly=0

# Pin 1  - SCK
# Pin 2  - SDA
# Pin 3  - usb 
# Pin 4  - 
# Pin 5  - aoss
# Pin 6  - router auto
# Pin 7  - router off
# Pin 8  - movie engine
# Pin 9  - 
# Pin 10 - 
# Pin 11 - reset button
# Pin 12 - CS0
# Pin 13 - CS1
# Pin 14 - 
# Pin 15 - 
# Pin 16 - 
# Pin 17 - 

# Don't flip on anything that isn't already enabled.
# Force on CS lines for flash devices, apparently this isn't done
# by uboot in normal booting.  No idea why. 
hint.gpio.0.function_set=0x00003004
hint.gpio.0.function_clear=0x00000000

# These are the GPIO LEDs and buttons which can be software controlled.
hint.gpio.0.pinmask=0x0001

hint.gpio.0.pinon=0x00000004

hint.gpioiic.0.at="gpiobus0"
#hint.gpioiic.0.pins=0x0003
hint.gpioiic.0.sda=0
hint.gpioiic.0.scl=1

# LEDs are configured separately and driven by the LED device
hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.name="red-diag"
hint.gpioled.0.pins=0x0001